| 001 | Currently printing. | 1. Previous print is not finished; please wait and retry. 2. Close and restart the program. |
| 002 | Requested start PASS is greater than the total PASS count of the task. | The print recovery parameters are incorrect; change the print settings. |
| 003 | Unauthorized system cannot print. | Contact the system supplier. |
| 004 | Incorrect system configuration. | Contact the system supplier. |
| 005 | Abnormal printhead voltage. | Check if the printhead is properly plugged in or if the carriage board is faulty. |
| 006 | Failed to generate stepping correction map. | Confirm if there is enough space on the software installation disk. |
| 007 | Authorization error. | Contact the system supplier. |
| 009 | Low ink or metering device inaccessible. | Check ink levels; check for card reader reading failure. |
| 010 | Previous print task processing has not finished. | 1. Wait and retry. 2. Restart the program. |
| 011 | Specified RIP data source does not exist. | 1. Specified RIP file no longer exists. 2. Network data connection is disconnected. |
| 012 | Unsupported color count in RIP file. | Color count exceeds system capability. |
| 014 | Unsupported DPI in RIP file. | Horizontal DPI exceeds system capability. |
| 015 – 018 | Channel parameter errors / configuration corrupt. | System configuration error or file damage. Backup parameters and reinstall software. |
| 019 | Insufficient memory for image processing. | Close large processes to free up memory for the software. |
| 021 | Unsupported PASS count. | Change PASS settings and restart printing. |
| 022 | Material is narrower than image width. | 1. Check material width. 2. Use wider material. 3. Use area printing. |
| 023 | Motion length exceeds machine platform length. | 1. Change motion buffer parameters. 2. Reinstall software if config is damaged. |
| 024 | Print position too close to zero; insufficient buffer. | 1. Move print position further from origin. 2. Reduce buffer length. |
| 025 | Insufficient platform Y-length. | Reduce the Y-dimension of the artwork. |
| 026 | Speed overclocking. | Reduce printing speed. |
| 027 | Insufficient acceleration or buffer length. | Increase acceleration and buffer length values. |
| 031 – 033 | Loading/Database creation failures. | Check file format and check for file damage. |
| 034 – 035 | Voltage/Ink parameter loading failure. | Check if board power and ink files are normal. |
| 050 / 061 | Carriage cannot return to zero. | 1. Check motor/electrical system. 2. Check/replace position encoder. |
| 062 | Material not found. | Check if the carriage edge sensor is working. |
| 063 | Edge finding error (partial detection). | Check edge sensor sensitivity. |
| 079 | Failed to add print task. | 1. File is in use. 2. Incorrect file format. |
| 080 | Specified RIP driver failed. | Check if software supports this RIP format. |
| 093 | Carriage lift reset timeout. | Check motor wiring and reset signals. |
| 098 | Printing error (Password). | Password nearly expired; enter password promptly. |
| 099 | USB mainboard not connected. | Check device power and USB connection. |
| 100 | Failed to update print speed. | Horizontal DPI does not support this carriage speed. |
| 111 | System control card not driven. | 1. Reinstall USB control card. 2. Replace damaged card. |
| 112 – 113 | Hardware/DSP program cannot load. | Control card may be damaged; install a new one. |
| 114 / 116 | Carriage card initialization error. | Card fault or power-on interval too short (wait 20s). |
| 117 | Voltage detection abnormal. | Carriage card hardware fault; check high/low voltage. |
| 118 | Fiber optic communication failed. | 1. Check carriage board. 2. Check fiber orientation. |
| 119 | Channel mapping failed. | Check carriage board and software version match. |
| 120 | Reset cancelled by user. | Do not press ESC during system reset. |
| 121 | Reset failed: Limit signal not detected. | Check limit switch circuit and functionality. |
| 122 | Reset failed: No encoder signal. | 1. Check carriage motor. 2. Check encoder connection. |
| 123 | Encoder signal phase reversed. | Reverse the AB phase signal connection. |
| 125 | Emergency stop pressed during reset. | Release E-stop and restart software. |
| 140 – 142 | Authorization/System mismatch. | Contact the equipment/system supplier. |
| 147 | Time-limited version expired. | Contact the system supplier. |
| 151 | Dongle not detected. | 1. Check installation. 2. Contact supplier. |
| 152 | Invalid dongle. | Dongle and board are a matched set; do not mix. |
| 155 – 157 | Dongle expired or usage limit reached. | Contact the system supplier. |
| 171 | Ink card reader not found. | Reconnect or reinstall reader driver. |
| 301 – 305 | Print data source disconnected. | Check data source and use “Resume Print.” |
| 309 | USB disconnected during printing. | Check USB connection. |
| 312 | Print process error. | USB board or X-raster count issue (common on Win10). |
| 410 | Printhead app/software mismatch. | Confirm software driver matches the printhead used. |
| 1999 | Printhead temp > set temp (by 2°C+). | Check wiring, driver board, or head board. |
