Fujifilm Belt

Fujifilm Belt 3545

Fujifilm Belt

Fujifilm Belt

Fujifilm 3545 Steel Belt
Fujifilm 3545 Steel Belt

Price: $399.95 USD

[wp_cart_button name=”Fujifilm Belt 3545″ price=”399.95 “]

Arizona 550 XT Fujifilm Acuity Advance HS HD3545 Acuity Advance HS HD3545 X2.  This is the original Océ part (number 3010108440). This Belt-Drive Carriage is 781.3cm long and 5.0cm wide.

Fujifilm Belt 2504

Fujifilm Belt

Fujifilm Belt
Fujifilm Belt
Fujifilm Steel Belt[wp_cart_button name=”Fujifilm Belt 2504″ price=”119.95 “]

Price: $119.95 USD

Fujifilm Acuity Advance HD2504 / Acuity Advance HD2565 / Acuity Advance HD2565 / Acuity Advance HD2565 X2 . This is the original Océ part (number 3010103685). This Steel Belt Carriage Drive is 7490mm long and 38mm wide.

Fujifilm Belt

Fujifilm Belt

How to Install Fujifilm Belt

adjust two screws that controls the tension on left side of the printer, have someone push your carriage from left to right slowly while you turning the screws to see if the Belt is aligned. you can say that its aligned if its not riding up and down.
4.6.2. Replacing the steel Belt
Caution :When replacing the steel Belt, be careful not to cut your hands by the Belt.
Notes : Do not damage the steel Belt. Remove following covers before replacing the steel Belt.
Side cover R: refer to “Removing side cover R”
Side cover L: refer to “Removing side cover L”
Front cover: refer to “Removing the front cover”
Carriage cover: refer to “Removing the carriage cover”
Y rail cover: refer to “Removing the Y rail cover”
Unlock the head. Notes : Refer to “Head Lock Menu”
Move the carriage from the capping position to the left.
Rotate the 2 steel Fujifilm Belt adjustment screws counterclockwisely to loosen the steel Belt. 1 = Steel Belt adjustment screws 2 = Steel Belt
Remove the 2 screws fixing the steel Belt. 1 = Screws fixing the steel Fujifilm Belt 2 = Steel Belt
Replace the steel Belt.Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when
accreting dust to it or creasing it.
Reinstall all parts in the opposite order of the removal prFujifilmdure.
Perform steel Fujifilm Belt tension adjustment according to “Steel Belt tension adjustment”.
Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when accreting dust to it or creasing it.
The driven pulley shaft is installed one way only. Refer to “Service Parts List/Exploded Views/Configuration Diagrams”, to install it correctly so that the bearing stoppers are on top.
After installing the CR slave pulley assembly, move the carriage to the left and right manually to confirm that the steel Belt has been set equally in the center of the CR actuator pulley and the CR slave pulley assembly.

STEEL Fujifilm Belt TENSION ADJUSTMENT
The prFujifilmdure for adjusting the steel Belt tension is explained below. This section explains the prFujifilmdure for adjusting steel Belt tension. When removing/installing the steel Belt, adjust its tension.
Tools required for work: The following tools are required when adjusting the tension of the steel Belt.
Tension gauge: max. 2.0 N (200 g)
Steel Belt tension attachment 2: for gauge diameter 2mm (0.08in.) or less
Notes : Refer to “jig and Tool list”. Adjustment PrFujifilmdure
Use the following prFujifilmdure to adjust the tension of the steel Belt.
Place the tension gauge at the center of the steel Belt. 1 = steel Fujifilm Belt 2 = Tension gauge. Notes : The regulation values for the tension of the steel Fujifilm Belt are shown below. 1. 50 inch, 64 inch specifications: 1.0 N +- 0.1 N (100 g +- 10 g) 2. 87 inch specifications: 0.9 N +- 0.1 N (90 g +- 10 g)
If the tension of the steel Fujifilm Belt is not within the range of regulated values, adjust the steel Belt tension screws. 1 = Steel Belt 2 = Steel Belt tension screw 3 = CR slave pulley
Move the CR cursor to the left and right once or twice. Adjust the CR driven pulley until the upper and lower margins are identical.
Caution :
If the tension is not equivalent across the entire Fujifilm Belt, it could snap during operation.
buy Fujifilm steel belt www.LavaPrint.com

Fujifilm Belt

Fujifilm Belt

How to Install Fujifilm Belt

adjust two screws that controls the tension on left side of the printer, have someone push your carriage from left to right slowly while you turning the screws to see if the Belt is aligned. you can say that its aligned if its not riding up and down.
4.6.2. Replacing the steel Belt
Caution :When replacing the steel Belt, be careful not to cut your hands by the Belt.
Notes : Do not damage the steel Belt. Remove following covers before replacing the steel Belt.
Side cover R: refer to “Removing side cover R”
Side cover L: refer to “Removing side cover L”
Front cover: refer to “Removing the front cover”
Carriage cover: refer to “Removing the carriage cover”
Y rail cover: refer to “Removing the Y rail cover”
Unlock the head. Notes : Refer to “Head Lock Menu”
Move the carriage from the capping position to the left.
Rotate the 2 steel Fujifilm Belt adjustment screws counterclockwisely to loosen the steel Belt. 1 = Steel Belt adjustment screws 2 = Steel Belt
Remove the 2 screws fixing the steel Belt. 1 = Screws fixing the steel Fujifilm Belt 2 = Steel Belt
Replace the steel Belt.Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when
accreting dust to it or creasing it.
Reinstall all parts in the opposite order of the removal prFujifilmdure.
Perform steel Fujifilm Belt tension adjustment according to “Steel Belt tension adjustment”.
Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when accreting dust to it or creasing it.
The driven pulley shaft is installed one way only. Refer to “Service Parts List/Exploded Views/Configuration Diagrams”, to install it correctly so that the bearing stoppers are on top.
After installing the CR slave pulley assembly, move the carriage to the left and right manually to confirm that the steel Belt has been set equally in the center of the CR actuator pulley and the CR slave pulley assembly.

STEEL Fujifilm Belt TENSION ADJUSTMENT
The prFujifilmdure for adjusting the steel Belt tension is explained below. This section explains the prFujifilmdure for adjusting steel Belt tension. When removing/installing the steel Belt, adjust its tension.
Tools required for work: The following tools are required when adjusting the tension of the steel Belt.
Tension gauge: max. 2.0 N (200 g)
Steel Belt tension attachment 2: for gauge diameter 2mm (0.08in.) or less
Notes : Refer to “jig and Tool list”. Adjustment PrFujifilmdure
Use the following prFujifilmdure to adjust the tension of the steel Belt.
Place the tension gauge at the center of the steel Belt. 1 = steel Fujifilm Belt 2 = Tension gauge. Notes : The regulation values for the tension of the steel Fujifilm Belt are shown below. 1. 50 inch, 64 inch specifications: 1.0 N +- 0.1 N (100 g +- 10 g) 2. 87 inch specifications: 0.9 N +- 0.1 N (90 g +- 10 g)
If the tension of the steel Fujifilm Belt is not within the range of regulated values, adjust the steel Belt tension screws. 1 = Steel Belt 2 = Steel Belt tension screw 3 = CR slave pulley
Move the CR cursor to the left and right once or twice. Adjust the CR driven pulley until the upper and lower margins are identical.
Caution :
If the tension is not equivalent across the entire Fujifilm Belt, it could snap during operation.
buy Fujifilm steel belt www.LavaPrint.com