OCE Belt

OCE Synchronous Belt

OCE belt

OCE Belt for CS6060/6100

OCE Synchronous Belt 250-S2M-10
OCE Synchronous Belt 250-S2M-10

Price: $11.95 USD[wp_cart_button name=”OCE Synchronous Belt” price=”11.95″]

OCE synchronous belt (64) is suitable for OCE CS6060 CS6100 Seiko Colorpainter 64S and 100S printers. This is the original Seiko part (number U00103427800 replacing number U00045985400). This synchronous belt has a circumference of 250mm and 10mm wide.

OCE 550 Steel Belt

OCE 550 Steel Belt

OCE 550 Steel Belt

OCE Arizona 550 Steel Belt 3010108440 | OCE 550 GT Steel Belt | OCE 550 XGT Steel Belt | Fujifilm Acuity Advance HS HD3545 Steel Belt | Fujifilm Acuity Advance HS HD3545 X2 Steel Belt
OCE Arizona 550 Steel Belt 3010108440 | OCE 550 GT Steel Belt | OCE 550 XGT Steel Belt | Fujifilm Acuity Advance HS HD3545 Steel Belt | Fujifilm Acuity Advance HS HD3545 X2 Steel Belt

Price: $399.95 USD[wp_cart_button name=”OCE 550 Steel Belt” price=”399.95″]

OCE Steel Belt Océ Arizona 550 GT / Arizona 550 XT Fujifilm Acuity Advance HS HD3545 Acuity Advance HS HD3545 X2. This Belt-Drive Carriage is suitable for Océ Arizona 550 GT / XT printers. This is the original Océ part (number 3010108440). This Belt-Drive Carriage is 781.3cm long and 5.0cm wide.

OCE 6060 Steel Belt

OCE 6060 Steel Belt

OCE 6060 Steel Belt

OCE Belt 6060 Steel Belt
OCE Belt 6060 Steel Belt

Price: $89.95 USD[wp_cart_button name=”OCE Belt 6060 Steel Belt” price=”89.95″]

This steel belt (64) is suitable for OCE CS6060  CS6100 Seiko Colorpainter 64S and HP Designjet 9000 printers. This is the original Seiko part (number U00101625600). This belt is 468.5cm long and 2.5cm wide.

OCE 350 Steel Belt

OCE 350 Steel Belt

OCE 350 Steel Belt

OCE Arizona 250 GT Steel Belt 3010103685 | 350 GT | 360 GT | 200 GT | 300 GT | Fujifilm Acuity Advance HD2504 Steel Belt | HD2565 X2 steel belt
OCE Arizona 250 GT Steel Belt 3010103685 | 350 GT | 360 GT | 200 GT | 300 GT | Fujifilm Acuity Advance HD2504 Steel Belt | HD2565 X2 steel belt

Price: $119.95 USD[wp_cart_button name=”OCE 350 Steel Belt” price=”119.95″]

Océ Arizona 250GT / 350GT / 350XT / 360GT / 360XT, 200GT / 300GT This Steel Belt Carriage Drive is suitable for Océ Arizona 250 GT printers. This is the original Océ part (number 3010103685). This Steel Belt Carriage Drive is 7490mm long and 38mm wide.

OCE Belt

How to Install OCE Belt

adjust two screws that controls the tension on left side of the printer, have someone push your carriage from left to right slowly while you turning the screws to see if the Belt is aligned. you can say that its aligned if its not riding up and down.
4.6.2. Replacing the steel Belt
Caution :When replacing the steel Belt, be careful not to cut your hands by the Belt.
Notes : Do not damage the steel Belt. Remove following covers before replacing the steel Belt.
Side cover R: refer to “Removing side cover R”
Side cover L: refer to “Removing side cover L”
Front cover: refer to “Removing the front cover”
Carriage cover: refer to “Removing the carriage cover”
Y rail cover: refer to “Removing the Y rail cover”
Unlock the head. Notes : Refer to “Head Lock Menu”
Move the carriage from the capping position to the left.
Rotate the 2 steel OCE Belt adjustment screws counterclockwisely to loosen the steel Belt. 1 = Steel Belt adjustment screws 2 = Steel Belt
Remove the 2 screws fixing the steel Belt. 1 = Screws fixing the steel OCE Belt 2 = Steel Belt
Replace the steel Belt.Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when
accreting dust to it or creasing it.
Reinstall all parts in the opposite order of the removal procedure.
Perform steel OCE Belt tension adjustment according to “Steel Belt tension adjustment”.
Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when accreting dust to it or creasing it.
The driven pulley shaft is installed one way only. Refer to “Service Parts List/Exploded Views/Configuration Diagrams”, to install it correctly so that the bearing stoppers are on top.
After installing the CR slave pulley assembly, move the carriage to the left and right manually to confirm that the steel Belt has been set equally in the center of the CR actuator pulley and the CR slave pulley assembly.

STEEL OCE Belt TENSION ADJUSTMENT
The procedure for adjusting the steel Belt tension is explained below. This section explains the procedure for adjusting steel Belt tension. When removing/installing the steel Belt, adjust its tension.
Tools required for work: The following tools are required when adjusting the tension of the steel Belt.
Tension gauge: max. 2.0 N (200 g)
Steel Belt tension attachment 2: for gauge diameter 2mm (0.08in.) or less
Notes : Refer to “jig and Tool list”. Adjustment Procedure
Use the following procedure to adjust the tension of the steel Belt.
Place the tension gauge at the center of the steel Belt. 1 = steel OCE Belt 2 = Tension gauge. Notes : The regulation values for the tension of the steel OCE Belt are shown below. 1. 50 inch, 64 inch specifications: 1.0 N +- 0.1 N (100 g +- 10 g) 2. 87 inch specifications: 0.9 N +- 0.1 N (90 g +- 10 g)
If the tension of the steel OCE Belt is not within the range of regulated values, adjust the steel Belt tension screws. 1 = Steel Belt 2 = Steel Belt tension screw 3 = CR slave pulley
Move the CR cursor to the left and right once or twice. Adjust the CR driven pulley until the upper and lower margins are identical.
Caution :
If the tension is not equivalent across the entire OCE Belt, it could snap during operation.
buy OCE steel belt www.LavaPrint.com

OCE Belt

How to Install OCE Belt

adjust two screws that controls the tension on left side of the printer, have someone push your carriage from left to right slowly while you turning the screws to see if the Belt is aligned. you can say that its aligned if its not riding up and down.
4.6.2. Replacing the steel Belt
Caution :When replacing the steel Belt, be careful not to cut your hands by the Belt.
Notes : Do not damage the steel Belt. Remove following covers before replacing the steel Belt.
Side cover R: refer to “Removing side cover R”
Side cover L: refer to “Removing side cover L”
Front cover: refer to “Removing the front cover”
Carriage cover: refer to “Removing the carriage cover”
Y rail cover: refer to “Removing the Y rail cover”
Unlock the head. Notes : Refer to “Head Lock Menu”
Move the carriage from the capping position to the left.
Rotate the 2 steel OCE Belt adjustment screws counterclockwisely to loosen the steel Belt. 1 = Steel Belt adjustment screws 2 = Steel Belt
Remove the 2 screws fixing the steel Belt. 1 = Screws fixing the steel OCE Belt 2 = Steel Belt
Replace the steel Belt.Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when
accreting dust to it or creasing it.
Reinstall all parts in the opposite order of the removal procedure.
Perform steel OCE Belt tension adjustment according to “Steel Belt tension adjustment”.
Notes : Be careful when handling the steel Belt. The steel Belt may be cut off when accreting dust to it or creasing it.
The driven pulley shaft is installed one way only. Refer to “Service Parts List/Exploded Views/Configuration Diagrams”, to install it correctly so that the bearing stoppers are on top.
After installing the CR slave pulley assembly, move the carriage to the left and right manually to confirm that the steel Belt has been set equally in the center of the CR actuator pulley and the CR slave pulley assembly.

STEEL OCE Belt TENSION ADJUSTMENT
The procedure for adjusting the steel Belt tension is explained below. This section explains the procedure for adjusting steel Belt tension. When removing/installing the steel Belt, adjust its tension.
Tools required for work: The following tools are required when adjusting the tension of the steel Belt.
Tension gauge: max. 2.0 N (200 g)
Steel Belt tension attachment 2: for gauge diameter 2mm (0.08in.) or less
Notes : Refer to “jig and Tool list”. Adjustment Procedure
Use the following procedure to adjust the tension of the steel Belt.
Place the tension gauge at the center of the steel Belt. 1 = steel OCE Belt 2 = Tension gauge. Notes : The regulation values for the tension of the steel OCE Belt are shown below. 1. 50 inch, 64 inch specifications: 1.0 N +- 0.1 N (100 g +- 10 g) 2. 87 inch specifications: 0.9 N +- 0.1 N (90 g +- 10 g)
If the tension of the steel OCE Belt is not within the range of regulated values, adjust the steel Belt tension screws. 1 = Steel Belt 2 = Steel Belt tension screw 3 = CR slave pulley
Move the CR cursor to the left and right once or twice. Adjust the CR driven pulley until the upper and lower margins are identical.
Caution :
If the tension is not equivalent across the entire OCE Belt, it could snap during operation.
buy OCE steel belt www.LavaPrint.com