Gerber Printer Parts

Gerber Encoder Board

Gerber Encoder Board

Gerber Encoder Board
Gerber Encoder Board

Price: $49.95 USD [wp_cart_button name=”Gerber Cat UV Encoder Board” price=”49.95″] This Gerber Cat UV Encoder P82508B – PKG is for the following printers: Gerber Cat UV Gerber Solara ion.

Gerber Steel Belt

Gerber Encoder | Gerber Steel Belt
Gerber Steel Belt

Price: $99.95 USD [wp_cart_button name=”Gerber Steel Belt” price=”99.95″] This Gerber Cat UV Steel Belt is for the following printers: Gerber Cat UV Gerber Solara ion.

Gerber Printhead

Gerber Konica Printhead KM512MHX UV 14PL
Gerber Konica Printhead KM512MHX UV 14PL

Price: $999.95 USD [wp_cart_button name=”Gerber Printhead KM512″ price=”999.95″] This Gerber Cat UV Printhead is for the following printers: Gerber Cat UV Gerber Solara ion.

Gerber UV Ink Valve Solenoid 12V

Gerber UV Ink Valve Solenoid 12V
Gerber UV Ink Valve Solenoid 12V

Price: $79.95 USD [wp_cart_button name=”Gerber UV Ink Valve Solenoid 12V” price=”79.95″] This Gerber Cat UV Gerber UV Ink Valve Solenoid 12V is for Gerber printers.

Gerber UV Ink Valve Solenoid 24V

Gerber UV Ink Valve Solenoid 24V
Gerber UV Ink Valve Solenoid 24V

Price: $79.95 USD [wp_cart_button name=”Gerber UV Ink Valve Solenoid 24V” price=”79.95″] This Gerber Cat UV Gerber UV Ink Valve Solenoid 24V is for Gerber printers.

Gerber UV Ink Pump 24V

Gerber UV Ink Pump 24V
Gerber UV Ink Pump 24V

Price: $29.95 USD [wp_cart_button name=”Gerber UV Ink Pump 24V” price=”29.95″] This Gerber UV Ink Pump 24V is for Gerber printers.

Gerber UV Ink Pump 12V

Gerber UV Ink Pump 12V
Gerber UV Ink Pump 12V

Price: $29.95 USD [wp_cart_button name=”Gerber UV Ink Pump 12V” price=”29.95″] This Gerber UV Ink Pump 12V is for Gerber printers.

Gerber Encoder Strip

Gerber Encoder Strip
The Same Width as Original Gerber Encoder Strip

Price: $129.95 USD [wp_cart_button name=”Gerber Encoder Strip 17202400″ price=”129.95″] This Gerber Cat UV Encoder is for the following printers: Gerber Cat UV Gerber Solara ion

Gerber SOLARA UV2 UV Lamp SO 055A

Gerber SOLARA UV2 UV Lamp SO 055A

Gerber SOLARA UV2 UV Lamp SO 055A | Gerber Encoder
Gerber SOLARA UV2 UV Lamp SO 055A

Price: $179.95USD[wp_cart: Gerber SOLARA UV2 UV Lamp SO 055A :price:179.95:end] Total Overall Length: 4.2 inches / 107 mm Arc Length: 2.17 inches / 55mm Tube Diameter: 0.59 inches / 15 mm

Gerber Printer Solara ion Cable

Gerber Printer Solara ion Cable

Gerber Printer Cable
Gerber Printer Solara ion Cable

Price: $79.95USD[wp_cart: Gerber Printer Solara ion Cable:price:79.95:end] This gerber Cable is for gerber printer long data cable that is from mainboard to head board.

Gerber Printer Solara ion Cable

Gerber Printer Solara ion Cable

Gerber Cable 9pin 25pin
Gerber Cable 9pin 25pin

Price: $129.95USD[wp_cart: Gerber Cable 9pin 25pin:price:129.95:end] This gerber Cable is for gerber printer HS,GS, AR600, ODYSSEY and all plotters with 9pin to 25 pin connections. long data cable that is from mainboard to head board.

Gerber Printer UV Ink Damper

Gerber Printer Solara ion UV Ink Damper

Gerber Printer Solara ion UV Ink Damper
Gerber Printer Solara ion UV Ink Damper

Price: $19.95USD[wp_cart: Gerber Printer UV Ink Damper:price:19.95:end] This Gerber Printer UV Ink Damper is for all gerber printers such as Solara, HS,GS, AR600, ODYSSEY and all plotters.

Gerber Printer UV Ink Damper

Gerber Printer Solara ion UV Ink Damper

UV Ink Damper Tubing
UV Ink Damper Tubing

Price: $24.95USD[wp_cart: Gerber Printer UV Ink Damper Tubing:price:24.95:end] This Gerber Printer UV Ink Damper Tubing is for all gerber printers such as Solara, HS,GS, AR600, ODYSSEY and all plotters. Up Tubing is 3″/7.5cm and down tubing is 8″/20cm. This uv ink damper is sealed perfectly to fit uv printer.

Gerber Printer UV Ink Reservoir

Gerber Printer Solara ion UV Ink Damper

gerber uv ink reservoir
gerber uv ink reservoir UV Ink Tank

Price: $79.95USD[wp_cart: gerber uv ink reservoir:price:79.95:end] This gerber uv ink reservoir is for all gerber printers such as Solara, HS,GS, AR600, ODYSSEY and all plotters. This gerber uv ink reservoir is sealed perfectly to fit uv printer.

Gerber Encoder Strip

How to clean Gerber Encoder Strip? You will need Isopropyl Alcohol, Cleaning Swabs and Paper Towels. Putting two drops of alcohol onto each side of the cleaning swab. Dab the swab on the paper towel to soak up any excess liquid. Wipe the exposed area of the Gerber encoder strip gently in one direction, do not try to scrub the strip or bend it. Repeat the cleaning for the back of the Gerber encoder strip. Put the machine into Cleaning Mode under the Maintenance Sub-Menu. You will now be asked to remove the maintenance cover on the left side of the printer. After the Head Carriage moves to the left side of the printer, continue to clean the area of the Gerber encoder strip that is now exposed over the docking area. Once the Gerber encoder strip has been cleaned, perform a Limit Initialization to reset the Head Carriage. All printer manufacturers use optical Gerber encoder strips in inkjet printers to tell the print head carrier how for it has moved and also when it return to home position. If you get a bad printer jam hat blocks the carrier this Gerber encoder strip can get disconnected and then the printer can not print anything. We are about to show you how to repair the strip if it is damaged and reinstall it so the printer can function again. This guide uses the Roalnd Printer as an example but the steps are the same for any printer that uses these Gerber encoder strips. The first thing to do is check the strip for damage. Check both ends and make sure the plastic is not torn. The ends should have an opening about 1/4 inch from the end as seen here. If your Gerber encoder strip is torn you can usually repair it with packing tape. Wrap the tape around the end several times and the use a small knife to cut the tape where the original hole was as seen below. Then cut the tape off the strip around the side and end. Now its time to reinstall the strip. The Gerber encoder strip attaches to retainer brackets and both sides of the printer and is threaded through the printhead carrier in the middle. You will need the carrier to be in the middle of the printer. To get it there you will need to power up the printer and open the cover like you were going to change the print heads. Power up the printer and the print heads should start to move to the side. When they get about the center of the printer you will need to pull the power plug so they stop moving. Connect one end of the Gerber encoder strip as seen here. Now thread the Gerber encoder strip through the carrier as seen here. The outside opening is about 1/2 inch but the slot the encoder goes in is only about 1/16in so be patient. Then connect the other end of the Gerber encoder strip, the left hard side is spring metal to tension the strip and keep it tight. Now if you reapply the power to the printer the carrier should move freely and move back to the right side. Close the printer cover and try a test print to see if it work. If you still get a carrier jam then the strip did not get inserted correctly through the carrier. This UV curing lamp is Gerber SOLARA UV2 UV Lamp SO 055A UV Curing Lamp Bulb digital inkjet printers and that is 100% compatible replacement. SO 055A More UV lamp at www.PolarLamp.com welcome to see you keep colors instructional web series today we gonna walk you through how to properly change the UV lamps on a Lava color large format digital. remember to make sure the printer is turned off. refer to our instructional video on powering off the printer. gather your materials it;s helpful to have a twin screw drivers. in order to have a place for all your materials and keep to have space to perform the lamp replacement. he will need a medium-sized head screwdriver. a small flathead screwdriver up into UV lamp. when changing one UV lamp it’s necessary to replace the other at the same time. disconnect the two wires that power the fame. and the wire that powers the main you be lame. grab your Philips head screwdriver. and remove the three fronts crews on the lamp housing. lift up the cover and set it aside remove the two screws. on the top back mourners the lamp housing up. lift up the lamp housing and place it gently on the flap. grab your flat head screwdriver. and loosen the wires the lamp out at the terminal. then remove the old UV lamp. from the lamp housing replace the old lamp with the new. you be lame two things to remember our. wine be careful when handling the UV lamps.don’t touch the lamp itself with your fingers to make sure it clicks into place on both sides run the two wires into their connectors on a terminal and secure the set screws with your flat head screwdriver make sure that they;re both secure. in certainly in Powys ing back into its position. secure the two back screws for. replace the cover and then secure the three fronts period. reconnect the fans and UV lamp power supplies. make sure that the two wires for the fans snap into place. and then you repeat the same procedure. to replace the other UV lamp. gerber uv ink at Gerber UV ink

Leave a Reply