Skyjet Encoder Sensor
Skyjet Encoder
Price: $49.95 USD
This Skyjet Encoder Sensor is for SKYJET UV FlatMaster2512. SKYJET UV FlatMaster2518. SKYJET UV FlatMaster3018. SKYJET UV Glass Master2512. SKYJET UV Glass Master2522. SKYJET UV Glass Master3022. SKYJET HS-3304KL-4C. SKYJET HS-3306KL-6C. SKYJET HS-3304KL-4C. SKYJET HS-3312KL-4C. SKYJET HS-3312KL-6C. SKYJET PSD-3316KL-4C. SKYJET PSD-3316KM-4C. SKYJET PSD-3324KL-6C. SKYJET PSD-3324KM-6C. SKYJET SM-1724XR-4C. SKYJET SM-1732XR-4C. SKYJET SM-1748XR-4C. SKYJET SM-1724XR-4C. SKYJET SM-3332XR-4C. SKYJET SM-3348XR-4C. SKYJET SM-5224XR-4C. SKYJET SM-5232XR-4C. SKYJET SM-5248XR-4C. SKYJET TPL-1908. SKYJET TPL-191.6 SKYJET TPL-3208. SKYJET TPL-3216.
Skyjet Encoder Strip
Price: $79.95 USD
This Skyjet Encoder SStrip is for SKYJET UV FlatMaster2512. SKYJET UV FlatMaster2518. SKYJET UV FlatMaster3018. SKYJET UV Glass Master2512. SKYJET UV Glass Master2522. SKYJET UV Glass Master3022. SKYJET HS-3304KL-4C. SKYJET HS-3306KL-6C. SKYJET HS-3304KL-4C. SKYJET HS-3312KL-4C. SKYJET HS-3312KL-6C. SKYJET PSD-3316KL-4C. SKYJET PSD-3316KM-4C. SKYJET PSD-3324KL-6C. SKYJET PSD-3324KM-6C. SKYJET SM-1724XR-4C. SKYJET SM-1732XR-4C. SKYJET SM-1748XR-4C. SKYJET SM-1724XR-4C. SKYJET SM-3332XR-4C. SKYJET SM-3348XR-4C. SKYJET SM-5224XR-4C. SKYJET SM-5232XR-4C. SKYJET SM-5248XR-4C. SKYJET TPL-1908. SKYJET TPL-191.6 SKYJET TPL-3208. SKYJET TPL-3216.
Skyjet Encoder Strip Skyjet Encoder Sensor
How to clean Skyjet Encoder? You should change your Skyjet Encoder if your printer can not print a Straight line perfectly, like Line dislocation or deflection. You will need Isopropyl Alcohol, Cleaning Swabs and Paper Towels. Putting two drops of alcohol onto each side of the cleaning swab. Dab the swab on the paper towel to soak up any excess liquid. Wipe the exposed area of the Skyjet Encoder gently in one direction, do not try to scrub the strip or bend it. Repeat the cleaning for the back of the Skyjet Encoder. Put the machine into Cleaning Mode under the Maintenance Sub-Menu. You will now be asked to remove the maintenance cover on the left side of the printer. After the Head Carriage moves to the left side of the printer, continue to clean the area of the Skyjet Encoder that is now exposed over the docking area. Once the Skyjet Encoder has been cleaned, perform a Limit Initialization to reset the Head Carriage. All printer manufacturers use optical Skyjet Encoders in inkjet printers to tell the print head carrier how for it has moved and also when it return to home position. If you get a bad printer jam hat blocks the carrier this Skyjet Encoder can get disconnected and then the printer can not print anything. We are about to show you how to repair the strip if it is damaged and reinstall it so the printer can function again. This guide uses the Roalnd Printer as an example but the steps are the same for any printer that uses these Skyjet Encoders. The first thing to do is check the strip for damage. Check both ends and make sure the plastic is not torn. The ends should have an opening about 1/4 inch from the end as seen here. If your Skyjet Encoder is torn you can usually repair it with packing tape. Wrap the tape around the end several times and the use a small knife to cut the tape where the original hole was as seen below. Then cut the tape off the strip around the side and end. Now its time to reinstall the strip. The Skyjet Encoder attaches to retainer brackets and both sides of the printer and is threaded through the printhead carrier in the middle. You will need the carrier to be in the middle of the printer. To get it there you will need to power up the printer and open the cover like you were going to change the print heads. Power up the printer and the print heads should start to move to the side. When they get about the center of the printer you will need to pull the power plug so they stop moving. Connect one end of the Skyjet Encoder as seen here. Now thread the Skyjet Encoder through the carrier as seen here. The outside opening is about 1/2 inch but the slot the encoder goes in is only about 1/16in so be patient. Then connect the other end of the Skyjet Encoder, the left hard side is spring metal to tension the strip and keep it tight. Now if you reapply the power to the printer the carrier should move freely and move back to the right side. Close the printer cover and try a test print to see if it work. If you still get a carrier jam then the strip did not get inserted correctly through the carrier. Just disconnect it and try again.
Skyjet UV Lamp
lavaink also stock all Skyjet uv lamps at Skyjet UV Lamp
Skyjet Parts
Skyjet Encoder Strip Sensor Board Printhead Damper Ink Pump Motor Skyjet Encoder Strip Sensor Board Printhead Damper Ink Pump Scan Motor for all skyjet uv printers 2512 3020 Printhead Rail Block Belt UV Lamp Solenoid Valve